This is an original planning guide. It is not a vendor manual, an official standard, or legal advice. Example addresses use documentation ranges. Review every command before you paste it.
What this hour is for
How to Configure VLAN Subinterface on Check Point Gaia is one lab change on a Check Point Gaia device you administer. A subinterface tags one VLAN on a router or firewall link. The parent link and the tag have to match the switch trunk. The browser tool drafts text. It does not log in. You still choose the device.
Check Point installs a policy package to a gateway. The package and the gateway are both named before install. Do not install to every gateway because the button is there. One tag, one address, the same id the switch allows on that trunk.
A subinterface for every VLAN you might need someday is a list, not this ticket. The tag matches both ends, and one host in that VLAN reaches the address. The previous revision of the package is the rollback.
192.0.2.0/24, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. They belong in the note. They are not prefixes you type onto a production device because they appeared in a draft. example.com is not your hostname. A second session stays open if the change can lock you out.
The change you can finish
Apply nothing during the writing of the note. When the lab window opens, it is one change on the device named in the ticket. Read the draft, then the device, then decide.
Rollback is the file or the revision you saved first. You do not invent a rollback after the only copy is gone.
- Write the hostname and confirm you administer it.
- Save the current config before any draft is applied.
- Generate the draft and delete every line this ticket did not name.
- Remove any 0.0.0.0/0 and any secret.
- Apply one change only when the lab window is open.
- Read the result back and compare it with the ticket.
- Stop. The next feature is a different page.
Mistakes that outlive the command
VLAN Subinterface on Check Point Gaia goes wrong in a small set of ways. The list is here so the ticket can forbid them before the window.
- Pasting a draft you did not read.
- The wrong hostname.
- A default password left in place.
- 0.0.0.0/0 kept from a sample.
- A secret in the ticket or in git.
- Two features in one window.
- No saved config before the change.
- A documentation prefix applied on a production device.
- A subinterface for every VLAN you might need someday is a list, not this ticket.
- Calling the generator output a finished production config.
Decisions to write down
One decision for VLAN Subinterface on Check Point Gaia: The hostname matches the ticket. The feature is only VLAN Subinterface. The vendor habit was followed: Check Point Gaia. A current config was saved first. No 0.0.0.0/0 remains. No secret is in the note. The proof you expect is: The tag matches both ends, and one host in that VLAN reaches the address. And the parent pillar still owns the design.
Checks before you call it done
Confirm this before you call the change done: The hostname was read from the device. The saved rollback exists. The draft was edited. One change was applied, or none yet because this was the writing hour. The read-back matches the ticket. A second person can say what changed. Management still works. And the next feature is not started. If one of those fails, stop.
# Check Point Gaia lab. Review before you paste.
# Feature: VLAN Subinterface.
# Check Point installs a policy package to a gateway. The package and the gateway are both named before install.
# Delete 0.0.0.0/0.
# prompt-for-this is not a password.
# 192.0.2.0/24, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. They belong in the note. They are not prefixes you type onto a production device because they appeared in a draft.Before you leave the device
How to Configure VLAN Subinterface on Check Point Gaia ends when the hostname on the device matches the hostname in the ticket. If it does not, you are on the wrong box. Stop. A command that succeeded on the wrong box is not progress.
The draft stays a draft until a person has read the names in it. A generator does not log into the device and does not know which interface is the uplink. You delete a line that names a device, a zone, or a prefix you did not write down.
0.0.0.0/0 is not kept because a sample included it. A source you can say is the source you keep. 192.0.2.0/24, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. They belong in the note. They are not prefixes you type onto a production device because they appeared in a draft.
Tools for this guide
These tools run in the browser on this site. They do not log into your machines.
Related pillar guides
More in this cluster
The pillar for this page, and the next published pages filed with it.