This is an original planning guide. It is not a vendor manual, an official standard, or legal advice. Example addresses use documentation ranges. Review every command before you paste it.
What this hour is for
A port number is a hint about a service, not proof the service is there. The lookup names a port you type. It does not connect. 22, 53, 80, and 443 are the ones most tickets mean. A high port can be anything.
One port. If you need to know whether your own host listens, that is the port-check page, one host you administer, not this reference. Do not turn the table into a target list.
This is a reference, not a standard you reprint and not a certification.
The change you can finish
Apply nothing during the writing of the note. When the lab window opens, it is one change on the device named in the ticket. Read the draft, then the device, then decide.
Rollback is the file or the revision you saved first. You do not invent a rollback after the only copy is gone.
- Type one port.
- Read the usual service.
- Write that it is a hint.
- Do not scan a host.
- Do not build a target list.
- Stop.
Mistakes that outlive the command
Well-Known Ports and Services goes wrong in a small set of ways. The list is here so the ticket can forbid them before the window.
- Scanning because the table listed the port.
- A port number called proof.
- A list of hosts beside the table.
- Calling the page the official registry.
Decisions to write down
One decision for Well-Known Ports and Services: One port was looked up. The name is a hint. No scan was run. No target list was made. And the page is a reference.
Checks before you call it done
Confirm this before you call the change done: The port is written. The usual service is written. The hint caveat is written. No host was scanned. And no list of targets was added. If one of those fails, stop.
| Port | Usual hint |
|---|---|
| 22 | SSH, if you meant SSH. |
| 80 and 443 | Web, clear text or TLS. |
| 53 | DNS. |
| Any other | Look it up. Do not assume, and do not scan. |
Before you leave the device
Well-Known Ports and Services ends when the hostname on the device matches the hostname in the ticket. If it does not, you are on the wrong box. Stop. A command that succeeded on the wrong box is not progress.
The draft stays a draft until a person has read the names in it. A generator does not log into the device and does not know which interface is the uplink. You delete a line that names a device, a zone, or a prefix you did not write down.
0.0.0.0/0 is not kept because a sample included it. A source you can say is the source you keep. 192.0.2.0/24, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. They belong in the note. They are not prefixes you type onto a production device because they appeared in a draft.
prompt-for-this is a reminder that a secret is missing. It is not a password, a key, a community string, or a pre-shared key you save in the ticket or in git. The real secret stays in the store.
One change is the window. A VLAN and a routing protocol and a VPN do not share it. If two things move and the result is wrong, you will not know which one did it. The next feature waits for its own page.
If the same step fails twice, stop for the day. The failure is the result. Adding a forum command beside a half-applied config produces a device nobody can rebuild. Restore the copy you took first.
A second person reads the device name and the change aloud. If they cannot find them in the ticket, the note is not done. Silence is not agreement. Then leave the device alone.
This page is a planning guide. It is not a vendor manual, not an official standard, and not a permission to touch a network you do not administer. The pillar guide owns the wider design. This page owns one lab proof.
Tools for this guide
These tools run in the browser on this site. They do not log into your machines.
Related pillar guides
More in this cluster
The pillar for this page, and the next published pages filed with it.