This is an original planning guide. It is not a vendor manual, an official standard, or legal advice. Example addresses use documentation ranges. Review every command before you paste it.
What this hour is for
How to Find Duplicate Indexes in IBM Db2 is one lab note for IBM Db2. A duplicate index repeats a key you already have. Dropping one is a later change after you save its definition.
IBM Db2. The client is the db2 command line. Do not put a password on the command line. Authentication stays on. Do not pipe a downloaded script to a shell. The file, when there is one, is a Db2 configuration or a SQL script. Do not open the Db2 port to every address. A starter that listens on every interface is edited first.
Do not drop an index during the reading. A unique constraint is not a duplicate you remove because it looks similar. The two indexes are named, the definition is saved, and nothing was dropped.
The generator drafts text in the browser. It does not log in. A header on a script says to review it before running, and a destructive line is supposed to stay a comment. You still read the draft. 192.0.2.10, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. example.com is a documentation name. They belong in the note. They are not values you leave on a database because a draft included them.
The change you can finish
Apply nothing while you are writing the note. When the lab window opens, it is one change on the database named in the ticket. Read the draft, then the database, then decide.
Rollback is the backup, the file, or the snapshot you saved first. You do not invent a rollback after the only copy is gone.
- Write the database name and confirm you administer it.
- Save a backup, a file, or a snapshot before any draft is applied.
- Read the draft and delete every line this ticket did not name.
- Replace a sample password, a bind to every address, and any secret.
- Apply one change only when the lab window is open.
- Read the result back and compare it with the ticket.
- Stop. The next change is a different page.
Mistakes that outlive the statement
How to Find Duplicate Indexes in IBM Db2 goes wrong in a small set of ways. The list is here so the ticket can forbid them before the window.
- Pasting a draft you did not read.
- The wrong database.
- A secret or a sample password left in the note.
- A listen address of every interface left in the file.
- Two changes in one window.
- No copy saved before the change.
- Disabling authentication, a firewall, or TLS to make a check pass.
- Calling the generator output a finished production change.
- Do not drop an index during the reading. A unique constraint is not a duplicate you remove because it looks similar.
Decisions to write down
One decision for How to Find Duplicate Indexes in IBM Db2: The database is IBM Db2. The change is only this duplicate-index report. A sample password was replaced or was never present. A listen on every address was removed or was never present. Nothing was applied during the reading. And the proof you expect is: The two indexes are named, the definition is saved, and nothing was dropped.
Checks before you call it done
Confirm this before you call the change done: The database name matches the ticket. The draft was read. No secret is in the note. Authentication was not disabled. The listen address is not every interface. And nothing was applied, or the lab window is still closed. If one of those fails, stop.
# IBM Db2. duplicate-index report.
# Review before you run.
# Replace a sample password.
# Delete a bind to every address.
# Do not disable authentication.
# 192.0.2.10, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. example.com is a documentation name. They belong in the note. They are not values you leave on a database because a draft included them.Before you leave the database
How to Find Duplicate Indexes in IBM Db2 ends when the database in the prompt is the database in the ticket. If it is not, you are on the wrong database. Stop.
The draft stays a draft until a person has read the names in it. A generator does not log into the database. You delete a line that names a host, a database, or an account you did not write down.
192.0.2.10, 198.51.100.0/24, 203.0.113.0/24, and 2001:db8::/32 are documentation. example.com is a documentation name. They belong in the note. They are not values you leave on a database because a draft included them.
prompt-for-this is a reminder that a secret is missing. It is not a password, a key, or a token you save in the ticket or in git. A sample password in a draft is replaced. It is not a password you keep.
One change is the window. If two things move and the result is wrong, you will not know which one did it.
If the same step fails twice, stop for the day. Restore the copy you took first.
A second person reads the database name and the change aloud. If they cannot find them in the ticket, the note is not done.
This page is a planning guide. It is not a vendor manual, not an official standard, and not permission to touch a database you do not administer. You do not disable authentication, a firewall, or TLS to make a check pass.
Tools for this guide
These tools run in the browser on this site. They do not log into your machines.
Related pillar guides
More in this cluster
The pillar for this page, and the next published pages filed with it.